Évaluer
Les évaluations seront publiées après vérification.
L'article a été ajouté.
Vespa (Piaggio) Vespa 125 (VM2T)
Description
Vespa 125 (VM1/VM2)
The VM1T is the evolution of the V33T and gets a completely new engine with cross flushing and the same 54 mm dimension for piston stroke and bore. The piston has a new, smaller shape of the nose and on the new cylinder head the spark plug is no longer installed centrally but at an angle of 45°. The inlet and outlet openings of the cylinder are now arranged 90° crosswise (outlet downwards, inlet to the side), so far they were mostly next to each other towards the luggage compartment side. The 3-speed transmission gets stronger gears and a larger shifting cross, the clutch is strengthened from 2/2 to 3/3 cork/steel discs. The new crankshaft no longer has mushroom-shaped cheeks, but round cheeks which allow better balancing.
The flywheel magneto ignition gets a new pole wheel with elongated inspection holes and ignition contacts which can now be easily adjusted with a screwdriver. The fan wheel cover has no more slots, but is closed except for a central round opening. The aluminium cylinder cap is reshaped and now encloses the entire cylinder. The toothed kick starter segment has new dimensions.
The rear brake drum is reinforced with a ring to minimize deformation due to thermal stress. The exhaust tailpipe is now led out just on the left side under the baggage compartment shoe, on the V33T it still ran to the rear on the right under the engine. The middle and rear parts of the frame are reinforced. The reinforcement in the upper leg shield bead, as well as the support plate of the leg shield cascade and the rear frame part are widened to give the frame a higher stiffness. The engine block, which is still made of aluminium, gets a new shape: it is no longer open at the sides, but has seven air slots through which the air for cylinder cooling reaches the fan wheel.
The swinging saddle is more comfortable and is equipped with two double conical springs and a chrome-plated handle for the passenger. The saddle cover is dark green. The diameter of the headlight on the fender has been increased from 95 to 105 mm, the rectangular taillight is wider. The shell-shaped light switch with 3 switch positions plus kill is now completely made of grey plastic and bears the Vespa lettering as a relief on the cover.
Clutch and throttle cable are now also led out of the grommets in the leg shield tunnel and then inside the handlebar tube to the lever or throttle slide. There are some minor changes to the clutch and brake lever, also on the brake lever the receptacle for the cable nipple is now inside the lever receptacle.
The footplate end pieces are no longer grooved up to the rivet and now have a small tongue instead, which holds the footplate rubbers better. Also the rivet heads have a different, now drop-shaped form. Compared to the V33T the tank capacity increases by 1.25 litres to 6.25 litres. The total weight of the scooter increases by 1.8 kg.
The VM2T differs from the first series only in a few details: new regulations of the Italian legislation, the new regulations of the European Union and the new regulations of the European Commission. Road traffic regulations require that the headlamp must be equipped with a parking light. Therefore, the light switch now has one more switch position and is slightly larger overall. The headlamp housing has a red indicator light on the upper side to check the function of the headlamp at night. The rectangular tail light is again slightly enlarged and remains the same on all (Italian) models up to 1958. Engine and luggage compartment jaws are still made of aluminium, only on the last models sheet steel may already be used. (Source: GSF)
Frame numbers by year of manufacture:
1952: VM1T 1001-8830 (quantity: 7,830)
1953: VM1T 8831-85870 (quantity: 77,040)
Total number of units: 84,870
1953: VM2T 85871-100619 (quantity: 14,749)
1954: VM2T 100620-176014 (quantity: 75,395)
Total number of units: 90.144
Original paint (MaxMeyer)
| Body: Grigio (Pastello) PIA135 (15048) |
 |
| Primer: Rosso Opaco (Antiruggine) PIA55 (10055M) |
 |
| Mounting parts: Grigio (Pastello) PIA135 (15048) |
|
| Véhicule (généralités) | |
|---|---|
| Modèle: | Vespa 125 (VM2T) |
| Année/s de production: | 1953, 1954 |
| N° de châssis: | VM2T |
| Production: | 90142 |
| Véhicule dimensions | |
| Longueur: | 1680 mm |
| Largeur: | 790 mm |
| Hauteur: | 960 mm |
| Hauteur de la selle: | 770 mm |
| Hauteur du marchepied: | 220 mm |
| Distance entre les axes de roues: | 1160 mm |
| Capacité réservoir d'essence: | 6.25 l |
| Poids (à vide): | 85 kg |
| Véhicule roues | |
| Roue avant: | 3.50 - 8 |
| Roue arrière: | 3.50 - 8 |
| Jante avant: | 2.10 - 8 |
| Jante arrière: | 2.10 - 8 |
| Véhicule freins | |
| Type de frein avant: | frein a tambour |
| Actionnement de frein avant: | mécanique par câbles |
| Ø avant: | 124 mm |
| Type de frein arrière: | frein a tambour |
| Actionnement de frein arrière: | mécanique par câbles |
| Ø arrière: | 126 mm |
| Véhicule moteur | |
| Cylindrée: | 123.7 cm³ |
| Course: | 54 mm |
| Alésage: | 54 mm |
| Type de moteur: | 2 temps |
| Nombre de cylindres: | 1 |
| Type de refroidissement: | par aire |
| Puissance (kW): | 3.31 kW |
| Puissance (ch): | 4.5 |
| Régime max. de rotation (puissance max.): | 5000 |
| Compression: | 1:6.5 |
| Carburation: | carburateur |
| Carburateur: | Dell'Orto TA 18C |
| Démarreur: | kick |
| Embrayage: | manuel |
| Fabricant du moteur: | Piaggio |
| Vitesse max.: | 75 km/h |
| Type de moteur: | 2 temps |
| Norme d'emissions: | sans |
| Véhicule moteur - allumage | |
| Type d'allumage: | avec rupteur |
| Avance à l'allumage: | 28 |
| Écartement des contacts: | 0.4 mm |
| Puissance (éclairage): | 36 W |
| Tension: | 6 V |
| Bougie: | (NGK) B7HS |
| Véhicule moteur - boîte de vitesses | |
| Boîte de vitesses: | manuelle |
| Nombre de vitesses: | 3 |
| Rapport transmission primaire - 1:: | 3.045 |
| Rapport 1re vitesse - 1:: | 4 |
| Rapport 2e vitesse - 1:: | 2.5 |
| Rapport 3e vitesse - 1:: | 1.593 |
| Rapport total - 1:: | 4.85 |
| Véhicule fluides | |
| Carburant: | Super (ROZ 95) |
| Mélange: | 1:25 |
| Huile de transmission: | SAE30 |
| Quantité huile de transmission: | 0.25 l |
| Les clients recherchaient alternativement | |
|---|---|
Derniers produits consultés