Write a review
Evaluations will be activated after verification.
Item successfully added.
Primary shaft -MCPROPARTS- Piaggio Ciao, Bravo, Si, Boxer MC MINA for vehicles with variator / Minarelli converter 10 teeth oblique
Part no.:
MC222217
Description
MCMINA CONVERSION KIT
The drive revolution for your Piaggio moped !
The wait is finally over !
After countless tests , over 2 years of development and thousands of kilometers
as well as hundreds of satisfied customers, the
MCMINA CONVERSION KIT is
finally available for everyone
and usable with a variety of possible gearbox combinations.
✅
What is the Mina Conversion Kit ?
Thanks to the Mina Conversion Kit consisting of :
- Primary shaft 10 teeth helical
CNC turned / milled from hardened steel with perfect concentricity up to high speed regions (14000 + umd/min tested)
- Converter unit
Precise on a 5 axis CNC converted scooter / Minarelli converter with 101mm diameter with 41° pitch
it is possible to use complete scooter technology on his Piaggio moped !
During the conversion & manufacturing strong attention was paid to precision and quality materials !
✅
The result is :
- no more problems with bad shifting
- no more problems with power over 5 hp
- no more problems with excessive belt wear / belt slippage
- no vibrations / imbalance (whirring) -
less power loss at the drive -
little to no bearing wear -
converter side full control range usable -
shifting behavior selectable ( 38 ° / 41 ° )
- better start / pull-through -
higher Vmax -
perfectly tunable (startup & holding speed)
- low wear
- no more crescent problems -
large selection of clutch bells -
large selection of clutches - large
selection of
back pressure springs -
works perfectly with MCBELT belts
✅
Required :
- Primary shaft 10 teeth helical
- converter unit with 41°
- converter bell (can be freely selected from the Minarelli shelf , recommendation in the manual)
- clutch (different selectable , recommendation in the manual ) - back
pressure spring of your choice eg.e.g. from Malossi (from the Minarelli Regal > suitable for your setup)
- A mono moped gearbox e.g.
a 10.73:1 (recommendation)
- The mono moped gearbox must be milled off at the cover something, turned or filed down
- 1x bearing 1x Simmering
✅
Info :
- Pushing the moped is no longer possible - because no starter pads available -
Cable starter or kicker motor is required -
Side parts must be machined rear -
It should be a belt with correct geometry & angle used such as the MCBELT
A detailed & detailed instructions in the form of a PDF is available in the download area.
In this everything is described to the smallest detail !
Including recommendations for back pressure springs , clutches & parts list.
AI-translation
The drive revolution for your Piaggio moped !
The wait is finally over !
After countless tests , over 2 years of development and thousands of kilometers
as well as hundreds of satisfied customers, the
MCMINA CONVERSION KIT is
finally available for everyone
and usable with a variety of possible gearbox combinations.
✅
What is the Mina Conversion Kit ?
Thanks to the Mina Conversion Kit consisting of :
- Primary shaft 10 teeth helical
CNC turned / milled from hardened steel with perfect concentricity up to high speed regions (14000 + umd/min tested)
- Converter unit
Precise on a 5 axis CNC converted scooter / Minarelli converter with 101mm diameter with 41° pitch
it is possible to use complete scooter technology on his Piaggio moped !
During the conversion & manufacturing strong attention was paid to precision and quality materials !
✅
The result is :
- no more problems with bad shifting
- no more problems with power over 5 hp
- no more problems with excessive belt wear / belt slippage
- no vibrations / imbalance (whirring) -
less power loss at the drive -
little to no bearing wear -
converter side full control range usable -
shifting behavior selectable ( 38 ° / 41 ° )
- better start / pull-through -
higher Vmax -
perfectly tunable (startup & holding speed)
- low wear
- no more crescent problems -
large selection of clutch bells -
large selection of clutches - large
selection of
back pressure springs -
works perfectly with MCBELT belts
✅
Required :
- Primary shaft 10 teeth helical
- converter unit with 41°
- converter bell (can be freely selected from the Minarelli shelf , recommendation in the manual)
- clutch (different selectable , recommendation in the manual ) - back
pressure spring of your choice eg.e.g. from Malossi (from the Minarelli Regal > suitable for your setup)
- A mono moped gearbox e.g.
a 10.73:1 (recommendation)
- The mono moped gearbox must be milled off at the cover something, turned or filed down
- 1x bearing 1x Simmering
✅
Info :
- Pushing the moped is no longer possible - because no starter pads available -
Cable starter or kicker motor is required -
Side parts must be machined rear -
It should be a belt with correct geometry & angle used such as the MCBELT
A detailed & detailed instructions in the form of a PDF is available in the download area.
In this everything is described to the smallest detail !
Including recommendations for back pressure springs , clutches & parts list.
€161.99 *
incl. VAT plus shipping costs
Available immediately (delivery time 1-3 working days*)
P
For this item you get
fidelity point/s
| Customers alternatively searched for | |
|---|---|
| | MC Mina | Minarelli Ciao | Minarelli Wandler Ciao | MC Proparts | MC MINA | Rollerwandler | Primärstift | Minarelli Primär | MC Mina | Minarelli Ciao | Minarelli Converters Ciao | MC Proparts | MC MINA | Roller Converters | Primary | Minarelli Primary | Minarelli Primary | |
Related items
Recently viewed items