Write a review
Evaluations will be activated after verification.
Item successfully added.
Engine casing Vespa PK125 XL2 - with E-start option
Part no.:
3331619
Description
SE125 engine housing from LML. The engine cases of the Indian LML Sensation 125 are 99% identical to those of the Vespa PK125 XL2. New Piaggio engine cases have not been available from Italy for years. The LML engine cases are therefore a very good and high-quality alternative.
Since NOS goods occasionally have flash rust on the metal parts.
For use in other smallframe vehicles, please view document under "Downloads".AI-translation
+----------+
Manufacturer Information
LML
80 Robinson Road 00/02
068898 Singapore - Singapore
http://www.lmlglobal.in/
privacy@godaddy.com
Responsible Person for the EU
Scooter Center GmbH
Kurt-Schumacher-Str. 1
50129 Bergheim-Glessen - Germany
https://www.scooter-center.com/
info@scooter-center.com
Since NOS goods occasionally have flash rust on the metal parts.
PK125 XL2 / PK125 ETS
The engine case can be used as a 1:1 replacement for PK125 XL2 and PK125 ETS.
Adapter 3330134 is required to fit an original XL2 shift cable.
PK50 XL2 / PK50 FL2 / PK50 HP / Motovespa PK75 XL
FEATURES
- Housing type: PK125 XL2
- Crankshaft type: PK 125XL2/ PK125 ETS (24/25mm cone)
- Bearing seat alternator side: Ø: 38mm (PX needle bearing)
- Shifter cable type: 1 rigid cable like PK XL2
- intake:
- Long rotary slide surface (42mm)
- Intake manifold: 3-hole
- Overcurrent design: original like V50, PK, PV
- Elestart possible: Yes
For use in other smallframe vehicles, please view document under "Downloads".
SHIFTING
The housing uses the 1-pull shifting technology of the XL2 models
Here, a rigid shift wire is used to link the shift gate. The attachment of the shift cable differs from that of the Italian models (the mounting hole is larger). If the engine is to be controlled with two shift cables (as on XL1, PV, V50 etc.), a conversion kit is available for this purpose (see "Accessories" for both).
The SE125 engine block already uses the modern shift components of the XL2 models internally. The shift arm no longer has a parallelogram. It is guided in a continuous bearing track, supported by a needle bearing and sealed by a shaft seal. For this reason, only XL2 gearshift components fit into the SE motor housing:
-XL2 shift arm + screw
- cable mount
- shift arm shaft seal
- shift arm bearing
These components are always required if no XL2 donor motor is available
.PERFORMANCE
The SE125 housings have a long rotary valve sealing surface (42mm). This allows the intake to be greatly enlarged, making them ideal for high-performance tuning on a rotary valve basis.
CYLINDER
The cylinder base bore is 61.5mm, making it suitable for all standard and common tuning cylinders (not Falc, Quattrini SP09 etc.). It does not need to be spindled.
INTAKE B
UTTONS
The intake manifold has a 3-hole mounting system, so the V50, PV125 manifolds do not fit here.
SCOPE OF DELIVERY
The housing is supplied without bearings, nuts or cylinder studs, but with all silent blocks/silent rubbers
+----------+
Manufacturer Information
LML
80 Robinson Road 00/02
068898 Singapore - Singapore
http://www.lmlglobal.in/
privacy@godaddy.com
Responsible Person for the EU
Scooter Center GmbH
Kurt-Schumacher-Str. 1
50129 Bergheim-Glessen - Germany
https://www.scooter-center.com/
info@scooter-center.com
€229.00 *
€269.00 *
(14.87% off)
incl. VAT plus shipping costs
Available immediately (delivery time 1-3 working days*)
P
For this item you get
fidelity point/s
| Customers alternatively searched for | |
|---|---|
| Motorgehäuse | Motorblock | Gehäuse | Block | Casing | Triebwerksschalen | Schalen | Motorschalen | Motorhälfte | Motorhälften | Gehäusehälfte | Gehäusehälften | Engine | Engine Casing | Crankcase | Crank Case | Motor Case | Carters Moteur | Carter | Cárter Motor | | |
Available versions
Related items
KR Automation
3333488
Conversion set PK XL2 -engine to 2-gear change cables -KR AUTOMATION- Vespa V50, PV125, ET3, PK S, PK XL
3333488
The item is ordered and will be in stock soon
€97.98
*
*incl. VAT plus shipping costs
variants
Polini
P2150435
Intake manifold conversion -POLINI 3-hole, rotary valve- for Vespa PK XL 3-hole engine in Vespa V50, PV125, ET3 chassis - AW=Ø34mm (Vergaser Ø28-30mm - PHBH, VHSH, PWK28, TMX30, Smartcarb 26-28)
P2150435
further versions from €38.04
-
Available immediately (delivery time 1-3 working days*)connection size Ø=28.5mm
-
Available immediately (delivery time 1-3 working days*)CS Ø=28.5mm (version Polini CP)
-
Available immediately (delivery time 1-3 working days*)connection size Ø=34mm
Recently viewed items