Write a review
Evaluations will be activated after verification.
Item successfully added.
Crankshaft -MAZZUCCHELLI Racing (rotary valve) 60mm stroke- Vespa PX200
Part no.:
1620008
Description
Sport crankshaft from Mazuchelli with 60mm stroke (+3mm compared to series). It is an ideal complement to all sport and racing cylinders. The intake timing angle is relatively long with this crankshaft which makes it more difficult to adjust with SI24/SI26 carburettors than with a Stoffi or BGM crankshaft.
The long intake timing after top dead center ensures that in the lowest speed range much of the mixture already sucked in is pushed back through the carburettor (so called This causes the mixture to be heavily greased and the engine runs unevenly and stutters. The ideal companion for this wave is therefore a larger carburettor which is inevitably accompanied by a longer intake stroke with this type of engine. This dampens the spitting back into the carburetor already relatively strongly, an additional mounted resonance chamber (so-called Boost Bottle) facilitates the adjustment of the engine additionally.
The larger carburetor cross section fits well to the long control angles of the shaft and makes a strong performance increase possible in the upper speed range opposite early closing crankshafts. Unfortunately also with losses in the engine elasticity.
The Mazuchelli shaft does not erect the same width at the rotary vane control cheek and at the shaft seal seat as the BGM shafts. Therefore the control slot in the engine housing cannot be widened as much as with a BGM crankshaft.
The additional stroke must be compensated for on cylinders designed for the standard stroke of 57mm. For this purpose use either a 1.5mm head OR a 1.5mm foot gasket. It is not necessary to work with a 3mm gasket. The additional stroke of 3mm is distributed over 1.5mm in the lower dead center direction and 1.5mm in the upper dead center direction.
AI-translation
The long intake timing after top dead center ensures that in the lowest speed range much of the mixture already sucked in is pushed back through the carburettor (so called This causes the mixture to be heavily greased and the engine runs unevenly and stutters. The ideal companion for this wave is therefore a larger carburettor which is inevitably accompanied by a longer intake stroke with this type of engine. This dampens the spitting back into the carburetor already relatively strongly, an additional mounted resonance chamber (so-called Boost Bottle) facilitates the adjustment of the engine additionally.
The larger carburetor cross section fits well to the long control angles of the shaft and makes a strong performance increase possible in the upper speed range opposite early closing crankshafts. Unfortunately also with losses in the engine elasticity.
The Mazuchelli shaft does not erect the same width at the rotary vane control cheek and at the shaft seal seat as the BGM shafts. Therefore the control slot in the engine housing cannot be widened as much as with a BGM crankshaft.
The additional stroke must be compensated for on cylinders designed for the standard stroke of 57mm. For this purpose use either a 1.5mm head OR a 1.5mm foot gasket. It is not necessary to work with a 3mm gasket. The additional stroke of 3mm is distributed over 1.5mm in the lower dead center direction and 1.5mm in the upper dead center direction.
A foot gasket increases the control angle of the cylinder and thus provides the prerequisite for a sporty and speed-oriented power delivery. For full power, however, the exhaust angle must often be increased to compensate for the disproportionately increased overcurrent angle compared to the exhaust angle. For everyday engines it is usually recommended to compensate the stroke with a 1.5mm head gasket.
Cylinders designed for 60mm stroke (Polini 221, Pinasco 225) do not require an additional compensating gasket.
- stroke: 60mm
- cross rod length: 110mm
- engines: PX200, Cosa200, Rally200 (Ducati ignition)
- clevis: 20mm (solid material)
- Necessary stroke compensation: 1,5mm (foot or head for cylinders for 57mm stroke)
AI-translation
€174.50 *
incl. VAT plus shipping costs
Available immediately (delivery time 1-3 working days*)
P
For this item you get
fidelity point/s
| Bearings | |
|---|---|
| sizes: | 16x20x20mm |
| Gudgeon pins | |
| diameter: | 16 mm |
| Crankshafts | |
| stroke: | 60 mm |
| thread rotor side: | M12x1,25 right-hand thread |
| thread drive side: | M12x1,5 right-hand thread |
| diameter crankwebs: | 98 mm |
| width crankwebs: | 40.1 mm |
| diameter bearing seat rotor side: | 25 mm |
| diameter bearing seat drive side: | 25 mm |
| diameter oil seal seat rotor side: | 24 mm |
| diameter oil seal seat drive side: | 31 mm |
| full circle crankshaft: | |
| rotary valve crankshaft: | |
| length rotary crankweb: | 196 mm |
| Vespa PX200 - intake timing for short rotary surface (46mm) (°): | 184 |
| Vespa PX200 - intake timing for long rotary surface (62mm fully modified) (°): | 203 |
| crankcase has to be milled: | |
| engine casing has to be modified: | |
| Connecting rods | |
| length connecting rod: | 110 mm |
| thickness connecting rod: | 5.6 mm |
| diameter small end connecting rod eye: | 20 mm |
| lubricating hole at small end bearing: | no |
| diameter crankpin: | 20 mm |
| lubricating hole at crankpin bearing: | notch |
| crankpin shims: | yes |
| Customers alternatively searched for | |
|---|---|
| Crankshaft | Crank | Kurbelwelle | Krukas | Vilebrequin | Cigüeñal | Albero | Albero Motore | Drehschieber | Vanne Rotative | Válvula Rotativa | Valvola A Disco Rotante | Rotary Valve | | |
Related items
bgm Pro
BGM1200TL
Bearing dummy crankshaft -BGM PRO- 613912 (25x62x12mm) - (used for crankshaft, drive side Vespa PX, T5 125cc, Rally180 (VSD1T), Rally200 (VSE1T), Sprint, GS150/GS3... - crankshaft, flywheel side, Sprint, GS150/GS3, VNA, VNB, VBA, VBB...)
BGM1200TL
The item is ordered and will be in stock soon
€12.30
*
*incl. VAT plus shipping costs
LML
1800030
Extractor -VESPA- bearing ring of bearing type NBI253815 (25x38x15mm) ignition side PX, Cosa, Sprint Veloce, LML 2-stroke, PK125 ETS
1800030
The item is ordered and will be in stock soon
€68.95
*
*incl. VAT plus shipping costs
Piaggio
1022313
Cluch nut tab washer -PIAGGIO- all Vespa Largeframe models (-1995) - clutch nut
1022313
The item is ordered and will be in stock soon
€2.59
*
*incl. VAT plus shipping costs
Piaggio
3333877
Small end needle bearing -PIAGGIO (16x20x20mm)- Vespa PX200, Rally180, Rally200, Cosa200, Vespa T5 125cc, Lambretta LI, LIS, SX, TV, DL, GP, Piaggio SKR, Typhoon 125, Gilera Runner125 FX, Runner180 FXR, Hexagon LX, LXT 2-stroke
3333877
The item is ordered and will be in stock soon
€8.04
*
*incl. VAT plus shipping costs
bgm Pro
BGM1034
Oil seal 31x62,1x5,8/4,3mm -BGM PRO FKM (E10/etahnol resistant) Metall, braun (used for crankshaft drive side Vespa PX (since 1984), T5 125cc, Cosa)
BGM1034
The item is ordered and will be in stock soon
€11.90
*
*incl. VAT plus shipping costs
RECOMMENDED
Kingwelle
KW0041
Clutch -KINGWELLE DragBikeClutch aluminium version- Vespa PX, T5, Rally, Cosa
KW0041
The item is ordered and will be in stock soon
€577.99
*
*incl. VAT plus shipping costs
Malossi
1120025
Intake manifold -MALOSSI rotary valve- Vespa PX80, PX125, PX150, PX200, Sprint, Rally180 (VSD1T), Rally200 (VSE1T) - CS=Ø34mm (carburetors Ø28-30mm - PHBH, VHSH, PWK28, TMX30, Smartcarb 26-28)
1120025
The item is ordered and will be in stock soon
€56.95
*
*incl. VAT plus shipping costs
Ersatzteile
Piaggio
3333877
Small end needle bearing -PIAGGIO (16x20x20mm)- Vespa PX200, Rally180, Rally200, Cosa200, Vespa T5 125cc, Lambretta LI, LIS, SX, TV, DL, GP, Piaggio SKR, Typhoon 125, Gilera Runner125 FX, Runner180 FXR, Hexagon LX, LXT 2-stroke
3333877
The item is ordered and will be in stock soon
€8.04
*
*incl. VAT plus shipping costs
Recently viewed items