Write a review
Evaluations will be activated after verification.
Item successfully added.
Crankshaft -BGM Original 57mm stroke- Vespa Sprint150 (VLB1T), GL150 (VLA1T), GT125 (VNL2T), GTR125 (VNL2T), VNB, VBA, VBB, T4, Super
Part no.:
7700010
Description
The BGM crankshafts are forged like in the good old Piaggio times. In forging, the material is pressed together under temperature and high pressure. This results in a higher density of the material. Heat is dissipated much better. The material is more resistant to distortion. This is a huge advantage compared to the remanufactured crankshafts of other manufacturers whose materials used often do not even reach the level of a series shaft.
Tuning:
The high quality of the material used also allows the use of very light-weight spur gears without the risk of crankshaft damage. This allows a better acceleration behaviour to be combined with a considerably increased durability of the engine. This is particularly important on engines with large displacement and high speeds.
Control angle:
The control angle of this crankshaft corresponds to that of a standard shaft.
Thus it is equally suitable for the construction of a standard 125cc engine as well as a solid 177cc road tuning.
AI-translation
Tuning:
The high quality of the material used also allows the use of very light-weight spur gears without the risk of crankshaft damage. This allows a better acceleration behaviour to be combined with a considerably increased durability of the engine. This is particularly important on engines with large displacement and high speeds.
Control angle:
The control angle of this crankshaft corresponds to that of a standard shaft.
Thus it is equally suitable for the construction of a standard 125cc engine as well as a solid 177cc road tuning.
The precise manufacturing, the used material as well as the good bearings allow many trouble-free tens of thousands of kilometers of mileage.
Design:
Crankshaft with so-called small cone (so-called Sprint engine of the first series). Such shafts can be recognized by the diameter of the shaft sealing ring on the alternator side. This is the surface which is located after the cone but before the bearing seat of the Limal bearing on the crankshaft stub. Even easier is the identification by the unusual polar wheel nut with the thread dimension M11x1,50 with collar.
- Sealing surface Lima Wedi Ø: 20mm
- Control angle: Standard
- Stroke: 57mm
- Connecting rod length: 105mm
- Connecting rod bearing top: 15mm
AI-translation
€132.99 *
incl. VAT plus shipping costs
Available immediately (delivery time 1-3 working days*)
P
For this item you get
fidelity point/s
| General | |
|---|---|
| EAN: | 4250366614632 |
| Bearings | |
| sizes: | 15x19x20mm |
| Gudgeon pins | |
| diameter: | 15 mm |
| Crankshafts | |
| stroke: | 57 mm |
| thread rotor side: | M11x1,5 right-hand thread |
| thread drive side: | M12x1,5 right-hand thread |
| diameter crankwebs: | 98 mm |
| width crankwebs: | 39 mm |
| diameter bearing seat rotor side: | 25 mm |
| diameter bearing seat drive side: | 25 mm |
| diameter oil seal seat rotor side: | 20 mm |
| diameter oil seal seat drive side: | 20 mm |
| width bearing seat rotor side: | 12 mm |
| full circle crankshaft: | |
| rotary valve crankshaft: | |
| width rotary crankweb: | 15.6 mm |
| length rotary crankweb: | 215 mm |
| Vespa PX125-150 - intake timing for long rotary surface (33mm) (°): | 147 |
| Vespa PX125-150 - intake timing for short rotary surface (53mm fully modified) (°): | 170 |
| crankcase has to be milled: | |
| engine casing has to be modified: | |
| Connecting rods | |
| length connecting rod: | 105 mm |
| thickness connecting rod: | 5.7 mm |
| diameter small end connecting rod eye: | 19 mm |
| lubricating hole at small end bearing: | no |
| diameter crankpin: | 22 mm |
| lubricating hole at crankpin bearing: | slot |
| crankpin shims: | yes |
| Customers alternatively searched for | |
|---|---|
| Kurbelwelle | Krukas | Vilebrequin | Cigüeñal | Albero | Crankshaft | Crank | Albero Motore | |
Related items
Piaggio
1022313
Cluch nut tab washer -PIAGGIO- all Vespa Largeframe models (-1995) - clutch nut
1022313
The item is ordered and will be in stock soon
€2.59
*
*incl. VAT plus shipping costs
Alternative items
Recently viewed items